Автор Тема: 3D printing your aquarium parts  (Прочитано 4014 раз)

0 Пользователей и 1 Гость просматривают эту тему.

Оффлайн SantaMonica

  • Постоялец
  • Сообщений: 102
  • Поблагодарили: 16
  • SantaMonica
    • Просмотр профиля
    • Algae Scrubbers
3D printing your aquarium parts
« : 07 Август 2013, 04:14:24 »
3D printing your aquarium parts

For those of you serious DIY folks, you may be interested in how you can make your own plastic aquarium parts by printing them on a 3D printer. Just this year, costs for the 3D printers have dropped to under $500 USD for a pre-built one, and under $200 USD for a kit. 3D printing of your plastic parts works well when:

1. You are good with computers.
2. You like trying new designs or colors.
3. The part is small, or can be put together with small parts.
4. The part does not require great strength.
3. There is no easier/cheaper way to get the parts.

Some aquarium parts, such as simple boxes or tubes, are not suited to 3D printing because they can be more easily made with simple plastic or acrylic shapes. But some parts are so complex that there is no other way to make them except to print them on a 3D printer. I'll be using 3D printers to make the next version of algae scrubbers because of the built-in air tubing, magnet compartments, holes, and bubble pathways that make it impossible for the part to be made (in one piece) any other way.

Some things I've learned that pertain especially to 3D-printed aquarium parts:

1. Only use ABS plastic, not PLA or PVA. The ABS plastic is the same type of plastic used in kid's LEGO toys and is very strong. PLA or PVA plastic, however, will slowly dissolve when underwater or when subjected to high temps.

2. Only use FDM (also called FF) printers. These are the types of printers which use coils of plastic filament. These are also the cheapest printers. Other types of printers such as SLA (liquid) use a photo-cured plastic that will get brittle under aquarium lights, and "powder-printers" make parts which are not water tight.

3. The 3D printed parts will not be "glossy smooth". They will instead be more like carbon fiber, with a texture (or lines) running in one direction through the whole part.

I'm too new at 3D printing to be able to recommend a particular printer, but I'm sure each reef or aquarium club has someone who has a 3D printer, and this is usually a great place to start.

Happy printing!



Оффлайн unsofter

  • Евгений
  • Администратор
  • Ветеран
  • *
  • Сообщений: 2120
  • Поблагодарили: 73
    • Просмотр профиля
    • http://img.unsofter.by/
Re: 3D printing your aquarium parts
« Ответ #1 : 07 Август 2013, 06:35:28 »
Давно уже присматриваюсь к 3D принтеру, но у нас, к сожалению, ценник пока еще так сильно не упал. Вещь полезная не только для аквариумных нужд, вернее сказать, но и для аквариумных нужд тоже..
Делаю программное обеспечение.
www.unsofter.by
Море в количестве 80 литров

Белорусский клуб аквариумистов

Re: 3D printing your aquarium parts
« Ответ #1 : 07 Август 2013, 06:35:28 »

Оффлайн Voodoo

  • Александр, Брест
  • Ветеран
  • Сообщений: 1404
  • Поблагодарили: 107
  • Приятная приятность
    • Просмотр профиля
    • Аквариумный портал
Re: 3D printing your aquarium parts
« Ответ #2 : 07 Август 2013, 15:59:01 »
Good idea.
TEMPORA MUTANTUR ET NOS MUTAMUR IN ILLIS.

Оффлайн Scavim

  • Ветеран
  • Сообщений: 589
  • Поблагодарили: 54
    • Просмотр профиля
Re: 3D printing your aquarium parts
« Ответ #3 : 07 Август 2013, 17:23:14 »
Yes this is very interesting but still quite expensive technology. Need to take into account not only cost of the printer itself but cost of the consumables. At least here it is still expensive and we need to wait a bit more.

I'll be using 3D printers to make the next version of algae scrubbers

Please keep us informed about the results.

Оффлайн SantaMonica

  • Постоялец
  • Сообщений: 102
  • Поблагодарили: 16
  • SantaMonica
    • Просмотр профиля
    • Algae Scrubbers
Re: 3D printing your aquarium parts
« Ответ #4 : 07 Август 2013, 18:14:16 »
The plastic is low cost... most parts will cost only a few dollars to print.

Some ideas: http://www.thingiverse.com

Оффлайн SantaMonica

  • Постоялец
  • Сообщений: 102
  • Поблагодарили: 16
  • SantaMonica
    • Просмотр профиля
    • Algae Scrubbers
Re: 3D printing your aquarium parts
« Ответ #5 : 21 Август 2013, 05:14:17 »
Summary of 3D printing links:

Endless things to print:
http://www.thingiverse.com/

General forum for all printers:
https://groups.google.com/forum/#!forum/3dprintertipstricksreviews

Massive forum for lots of printer kits and DIY:
http://forums.reprap.org/

Current lowest-cost assembled printer to print aquarium-safe ABS plastic:
http://www.kicktraq.com/projects/pirate3d/the-buccaneer-the-3d-printer-that-everyone-can-use/

Current most popular U.S. based assembled printer:
http://makerbot.com/

Low cost Chinese clone of Makerbot:
http://www.ff3dp.com/

Another low cost Chinese clone of Makerbot:
http://www.wanhao3dprinter.com/

Оффлайн Voodoo

  • Александр, Брест
  • Ветеран
  • Сообщений: 1404
  • Поблагодарили: 107
  • Приятная приятность
    • Просмотр профиля
    • Аквариумный портал
Re: 3D printing your aquarium parts
« Ответ #6 : 21 Август 2013, 18:51:35 »
Low cost Chinese clone of Makerbot:
http://www.ff3dp.com/

Another low cost Chinese clone of Makerbot:
http://www.wanhao3dprinter.com/

Thank you very much for there links.
TEMPORA MUTANTUR ET NOS MUTAMUR IN ILLIS.

Оффлайн SantaMonica

  • Постоялец
  • Сообщений: 102
  • Поблагодарили: 16
  • SantaMonica
    • Просмотр профиля
    • Algae Scrubbers
Re: 3D printing your aquarium parts
« Ответ #7 : 29 Август 2013, 20:16:15 »
Here's my attempt at getting some printers for aquarium parts:
http://www.kickstarter.com/projects/1079197168/1221025490?token=347e500b